Is your GE washer not working? Fortuitously, this information for repairing your GE washer will information you thru the required steps. These are the precise procedures I observe when professionally repairing washers. Subsequently, fastidiously assessment every part, and your washer will operate once more very quickly.
In case your washer just isn’t working, there may very well be a number of points, however first, it is advisable to slender down the chances. Start by turning the timer knob to the “spin” setting after which switching on the washer. Pay shut consideration to the sounds you hear. If it seems that the motor is working (you might also hear the pump working), however the tub just isn’t turning, proceed to the part on checking the belt. If you happen to solely hear the pump working, begin from the start.
Key Information
- Widespread Causes: Defective lid change, broken belt, faulty timer, or motor points.
- Primary Parts to Verify: Lid change actuator, magnetic lid change, motor, belt, and clutch.
- Fast Repair Tip: Use an ohmmeter to check the lid change for continuity — change it if there’s no studying.
- Alternative Half Instance: Lid change (Half No. WH12X1044 for 6-inch model).
- Different Choice: Velocity Queen washers — recognized for commercial-grade reliability.
Causes Why GE Washer Is Not Working
Mechanical Lid Swap
Essentially the most frequent challenge inflicting GE washers to not run associated to the lid change. A malfunctioning lid change may end up in the washer not spinning or washing. Nonetheless, it is doable that the issue lies with the lid change actuator. Lid change actuators are current solely in washers geared up with mechanical lid switches.
These actuators encompass two elements: one on the washer’s lid and the opposite on the lid change situated beneath the washer’s casing (on the prime, beneath the lid the place there’s a gap). Typically, the difficulty happens when the actuator on the lid change turns into dislodged. In such a case, if you examine the opening beneath the actuator, it ought to seem empty.
To resolve this drawback, observe these steps:
- Take away the entrance panel of the washer (insert a butter knife between the highest and entrance, pushing on the clips).
- Seek for the actuator, which is oval and white, often discovered on the backside of the washer.
- If you happen to discover the actuator, take away the highest of the washer and reattach it (it ought to snap again into place). Making use of some adhesive to stop it from falling off once more is advisable.
- Look at the lid to test if the opposite actuator has additionally indifferent. If it has, it requires alternative.
- If there are not any points with the lid change actuator, the lid change itself could also be defective. To test this:
- First, unplug the washer.
- Take away the highest of the washer (secured by two screws behind the entrance panel).
- Use an ohmmeter to test for continuity between the 2 wires you needed to unplug to take away the highest. There must be continuity between the 2 wires when the lid is closed; if not, the change is flawed and desires alternative.
There are two sorts of mechanical lid switches obtainable, differing in size. The half quantity for the six-inch one is WH12X1044.
Magnetic Lid Swap
Magnetic lid switches sometimes have a low failure fee, and once they do fail, it is typically as a consequence of exterior components corresponding to one thing coming into contact with the highest of the washing tub and damaging the wires. Nonetheless, in case you suspect that the magnetic lid change is defective (after exploring different potential points), you may carry out a test. Listed below are the steps:
- First, make sure the washer is unplugged.
- Take away the entrance panel (you are able to do this by inserting a butter knife between the highest and the entrance panel and gently pushing on the clips to launch it).
- Reduce the wires related to the lid change, however be sure that to depart sufficient wire in case it is advisable to reinstall it.
- Utilizing an ohmmeter, test for continuity between the wires going to the lid change.
- When you have continuity with the lid within the closed place, the change remains to be functioning correctly. If there isn’t any continuity, then the change is certainly defective and must be changed.
Execs and Cons GE Washer
Execs
- Reliability
- Effectivity
- Selection
- Superior Know-how
- Sturdiness
Cons
- Worth
- Complexity
- Repairs
- Noise
- Restricted Availability
Variations Between GE Washers and Maytag Washers
GE
Whereas GE home equipment are typically dependable, repairs can typically be extra advanced, and discovering alternative components might require help from approved service suppliers.
Maytag
Maytag home equipment are sometimes lauded for his or her ease of restore and upkeep. Alternative components are extensively obtainable, and DIY repairs could also be extra possible.
Different to GE Washer
Velocity Queen
Velocity Queen is a model recognized for its commercial-grade sturdiness. If you happen to prioritize strong building and reliability, their washers could also be a sensible choice.
Timer Or Motor
Checking timers generally is a advanced job. Nonetheless, if the lid change is functioning appropriately, a defective timer may very well be the difficulty. The one different potential trigger can be a malfunctioning motor. It is value noting that timers are inclined to malfunction extra often than motors. To find out whether or not the timer is the issue, you may study the voltage on the motor. Defective motors typically emit a buzzing sound.
Nonetheless, it is important to grasp that the process for checking motor voltage can differ considerably primarily based on the washer mannequin, making it too dangerous for me to offer particular directions. In case you are accustomed to studying wiring diagrams, it is best to discover one close to the timer that will information you.
Nonetheless, I strongly advise in opposition to trying this process except you’re extremely skilled, and in case you do select to proceed (which I don’t advocate), train excessive warning and make sure the washer is on, taking care to not expose your self to electrical shock. Must you discover no voltage on the motor throughout this course of, think about changing the timer. Conversely, in case you do detect voltage on the motor, changing the motor could also be crucial.
Belt
In case your washer is not functioning correctly, significantly if it is not spinning or washing, it is doable that the difficulty lies with the belt. To evaluate the situation of the belt, observe these steps:
- Start by making certain the washer is unplugged to make sure security.
- Take away the entrance panel by gently inserting a butter knife between the highest and the entrance, utilizing it to press on the clips to launch the entrance panel.
- Find the belt beneath the transmission and punctiliously examine it to find out whether it is both damaged or excessively worn.
Clutch
The clutch serves as a mechanism that permits the motor to achieve its full velocity earlier than participating with the transmission. It is vital to notice that GE has discontinued using clutches of their washers for a while, so your washer might not function a clutch. In such circumstances, there’ll sometimes be a easy pulley situated on the backside of the motor.
There are two widespread points related to clutches. First, the clip that secures it to the motor can break, inflicting the clutch to detach. If this happens, it is best to change the clip and examine the belt, because it may need sustained harm when the clutch got here off.
The second challenge with clutches is once they break in half. In such conditions, it is advisable to switch each the belt and the clutch.
Conclusion
when confronted with the difficulty of a GE washer not working, it is important to systematically diagnose and tackle the potential causes. Widespread culprits might embody issues with the lid change, belt, transmission, or clutch.
Rigorously analyzing every of those elements and in search of skilled help when wanted might help restore your washer’s performance and guarantee its continued dependable efficiency. Bear in mind, security ought to at all times be a prime precedence when coping with equipment troubleshooting and repairs.
Authoritative References
-
GE Home equipment – Washer Troubleshooting Information
-
Residence Depot – GE Washer Restore and Elements
-
Restore Clinic – Learn how to Repair a GE Washer That Gained’t Begin
-
Shopper Studies – Washing Machine Troubleshooting Ideas
